-
Calcined Kaolin
-
Ultra Calcined Kaolin
- Ultra white and ultra-fine calcined kaolin for coating industry
- Ultra white and ultra-fine calcined kaolin for paper industry
- Ultra white and ultra-fine calcined kaolin for wire and cable
- Ultra white and ultra-fine calcined kaolin for rubber industry
- Ultra white and ultra-fine calcined kaolin for crop protection
- Ultra white and ultra-fine calcined kaolin for plastic masterbatch
- Ultra white and ultra-fine calcined kaolin for agricultural film insulation agent
- Special Calcined Kaolin
- Modified Calcined Kaolin
- Common Calcined Kaolin
-
Ultra Calcined Kaolin
- New Materials
- Metakaolin
- Superfine Nano Kaolin
- Hydrated kaolin products for Rubber
- Titanium Dioxide Slurry for Textile Coating
- Acrylic resin for coatings
- Calcined kaolin for Cement Industry
- Calcined kaolin products for ceramics
- Calcined kaolin products for Rubber
- Calcined kaolin products for engineering plastics
- Calcined kaolin products for wire and cable
- Calcined kaolin products for papermaking
- Calcined kaolin products for coatings
- Crop protectants
Finishing Fire Retardant Paint-Two-component water-based expansion type SH-S/700AB
1. Product indicators
| Component A | Index | |
| 1 | Appearance | Yellow liquid |
| 2 | Solid content (Wt%) | 46±1 |
| 3 | Viscosity (mPa.s) | ≤500 |
| 4 | pH | 6.0-8.0 |
| Component B | Index | |
| 1 | Appearance | White paste |
| 2 | Solid content (Wt%) | 66±2 |
| 3 | Average particle size µm | ≤20 |
2. Usage process
1. Before using this product, the wood needs to be polished smooth and the wood needs to be sealed with water-based primer.
2. You can also use component A to seal the substrate, the recommended dosage is 50-80g/m2. If the viscosity of component A is too high, add about 5% water to dilute it.
3. After treating the wood with component A, dry it for about 30 minutes before spraying the fire retardant coating. If the wood surface is slightly sticky, it will not affect the use of the fire retardant coating.
4. This product can be applied by brush, roller or spray. It is recommended to mix component A and component B in a weight ratio of 2:3 during construction, stir at high speed, and filter with a 100 or 120 mesh filter after stirring evenly. If the viscosity of the paint is too high during spraying, it is recommended to add 10-25% water for further dilution and stir evenly. When spraying, it is recommended to use a large-caliber spray gun and a high-power air pump for good spray atomization effect. The recommended construction amount is 90-120g/m2 each time.
5. The recommended wet glue dosage is 400-600g/m2. The principle of coating the product is to apply it in small amounts and multiple times. Wait until the previous coat is dry before applying the next coat, otherwise it may cause the coating to turn white.
3. Notes
1. Dilute component A with water. It is recommended that the amount of water used should not exceed 10%.
2. When spraying component A and component B, it is recommended that the amount of water used should not exceed 25%. The more water used, the longer the coating curing time.
3. Avoid working on rainy days during construction. It is recommended to use in an environment with air humidity <60%, temperature >20℃ and good ventilation. When the coating reaches the required thickness, it should be covered with waterproof varnish in time after the surface is dry for 24 hours to protect the fire retardant coating.
4. After the product is fully stirred and mixed, please use it within 2 hours, otherwise it will slowly solidify.
5. The flame retardant effect is directly related to the amount of spraying. The more the amount of spraying, the better the flame retardant effect.